• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace window hinges to Fix a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for most homeowners. However, if the holes for screws are smashed and aren't able to hold screws, you may need to use wood glue and dowels before you can install the hinge.

Clean up any surface corrosion. This will help keep the dowels in place and provide a solid base to hold onto.

Removing the Hinges

Many standard door hinges are removable, which makes it easier to move the door from one side to the next or to remove the entire door off the frame should it be needed. Anyone with a bit of patience can remove the hinges however, you must know what to do.

If the hinges are painted you will need to remove the paint prior to attempting to remove the pins. If you don't, the paint could be smashed off and scratch the door when you attempt to lift it. To break the seal put the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. Allow the hinges to sit in the pan for approximately 30 minutes. The heat from the water will soften the paint making it easier to take off.

Once the pins are loosened, remove the hinges and frame from the door. You can use a screwdriver to get the job done, but it is recommended that you employ a magnetic screwdriver to complete this project. This type of screwdriver is specifically designed to grab metal screws and assist you in getting the task done much faster.

Before you attempt to remove the hinges, it is a good idea to spray them with a lubricant. A simple lubricant can make the process move along quickly and make it easier to remove the screws and pins. You can find this kind of lubricant at most hardware and home improvement stores.

It is important to keep in mind that the number of door hinges you will need will vary depending on the type of door and its setting. Heavy doors and solid-core doors will require more hinges, while hollow-core doors that weigh less might require just two or three hinges.

It is also important to know the various types of hinges in order to determine which ones will best suit your needs. Exterior hinges are typically designed to support the door's weight however, interior hinges will require to handle lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may become loose and start to slide or hang crookedly. This can cause problems, but it's usually easy to repair window hinges. In most cases, a simple retightening of the screw will fix the issue. However in the event that the screw holes are ripped out, this can be more difficult to accomplish. A wood dowel can be used to tighten these holes again.

Start by drilling out the old hole using the drill bit that is similar to the size of the new screw (typically 3/8"). Then, you can use a wood glue as well as dowels made of wood to fill the hole. The dowel should be cut to a length similar to the screw to ensure a snug fit. Then, reinstall the screw and tighten it to the desired tightness. If the door does not stop bind up, insert a second dowel into the gap. Repeat the procedure. Make sure to close the door slowly in order to verify the clearances at the perimeter after each adjustment.

You can also use a wooden plug instead of the dowel. It works equally well, but may take a little longer to put in. You can use the wood piece which has been cut to the proper size. If you don't have a woodworking tool you could also try using toothpicks or wooden matches as well.

Use a countersink to make the hole smaller for the head of screw after you have reinstalled it. This will prevent the screw from hitting the edge of the doors when they are opened and closed. This will make it easier to tighten the screws after installing hinges.

Once you have reinstalled the window hinge repair cost, make sure to grease it with a dry lubricant in order to ensure that it doesn't get stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a thin coat and give it about 15 minutes to fully reach the barrel of the hinge.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you could make a few minor repairs. The first step is to ensure that the screws holding the hinge plate to the door and frame are tight. If they're loose, tighten them with a power drill or screwdriver. Be cautious not to tighten the screws to the point that they start to create gaps in the trim joints or, even more damagingly cause threads to be stripped.

If the problem is the hinge plates are separating and you want to reattach the plates by applying wood glue on the back of them and inserting wooden dowels or toothpicks in the holes. Dowels and toothpicks provide a solid foundation for the screws, preventing the plates from moving as you insert them. Allow the glue to dry before reattaching the hinge.

Another reason for loose hinges is that the screws are stripped or gone. This problem can be fixed by replacing the screws. Use a drill bit that is the same size as the screw hole to prevent drilling into the jamb or hinge.

Close the door after you've reattached the hinge and check the gap between the frame and the door. It should be about the thickness of a nickel all around or less if there's a gap caused by a door that was not properly hang. If the hinges were installed correctly, this should not be an issue.

If you notice that the replacement hinges for upvc windows remain loose, you can try adding an extra thicker shim between the hinge plate and the mounting surface, to create an extra inch of space. You could also try removing the hinge pin from the troublesome hinge and pounding it down using a hammer to make it tighter or use an entirely new hinge pin. You can also lubricate the hinges with mineral or Jojoba oil to decrease friction and aid in holding their place. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

The friction caused by the hinge's constant motion draws dust particles. These particles can become stuck and build up in the moving parts of door hinges if they are not regularly cleaned and lubricated. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection will preserve the functionality and quality of hinges that are attached to doors.

Inspect the hinges to see how much rust has accumulated on their surfaces. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you are able to save the hinges, begin by brushing off any loose rust with steel wool and a wire brush. Apply a commercial rust-removing product or a homemade solution such as lemon juice on the hinge. Allow the rust remover to remain on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

If you do not want to spend the cost and time to replace hinges, simply tightening the screws can bring back the Upvc Window Hinge Adjustment's functionality. If you've sanded the screws however, it could be necessary to attach an wooden dowel or shim to the hinge. Dowels made of wood are round pieces of wood in the form of rods which are available in different lengths and diameters. They can be purchased on the internet, at stores selling woodworking supplies and at home improvement stores.

You can also make a shim from a piece made of plastic or metal depending on the type hinge you have. To make a dowel, cut an unfinished dowel into the desired length. You can then dip the dowel in a glue for carpenters and then insert it into the stripped hole and let the glue hold the dowel in the right position.

Before cleaning the hinges, lay down a cloth or towel to protect your flooring from spills. After the area is secured, proceed to clean the hinges with a soft cloth or sponge coated with a mild cleaner or vinegar to remove dirt, grime, and tarnish. A toothbrush or small brush can be used to access difficult-to-reach places in crevices and difficult places.